Our coalescing filter elements are completely disposable, made entirely from borosilicate glass microfiber. The coalescing elements have a two-layer structure, an inner particle capture-layer and an outer drainage layer. Liquid droplets remain mobile once captured, and travel through the fine-pored capture-layer, along the intersecting microfibers, growing in size as they progress. These coalesced droplets are transferred to the large-pored drainage layer from where they drain by gravity into the filter bowl. Coalescing elements should always flow from the inside to the outside of the element so that proper draining of liquids can occur. These elements will simultaneously collect liquids and particulates.
Elements are specifically designed for the removal of liquid aerosols and particulate from gases in both corrosive and non-corrosive applications. The C type element is constructed of two layers of borosilicate microfiber.
Typically Used In Our Point-of-Use Filters
Technical Information:
Efficiency at 0.01 microns. Suffix Grade designation:
99.99998%99.9999%+99.99%+99.5%+95%
+75%30C40C50C60C70C
80COur 70C is recommended for optimal filtration by providing high flow rates and long element life at peak efficiency.
Elements are designed for heavy coalescing, CNG, and vacuum pump exhaust. Good to 900°F.
Typically Used with Our High Flow 3/4” NPT Filter Housings and Above.
Technical Information
Efficiency at 0.01 microns. Suffix Grade designation:
99.99998%99.9999%+99.99%
+99.5%+95%
+75%30CS40CS50CS
60CS70CS
80CSOur 70CS is recommended for optimal filtration by providing high flow rates and long element life at peak efficiency.
The 50CS is recommended for the coalescing of oils in vacuum pump exhaust applications.
These Elements are designed for heavy coalescing applications. Commonly used in CNG applications where added strength is needed due to heavy particulate loading and extremely contaminated coalesced oil. Good to 900°F .
Technical Information:
Efficiency at 0.01 microns. Suffix Grade designation:
99.99998%99.9999%+99.99%+99.5%+95%
+75%30CSX140CSX150CSX160CSX170CSX1
80CSX1Our 70CSX1 grade is recommended for optimal filtration by providing high flow rates and long element life at peak efficiency.
All of our coalescing elements can be caged by adding suffix X1; including the C and RC Grades.
*X1 Caged on the outside only compatible for use with any of our standard filter housings.
These Elements are designed for heavy coalescing applications. Commonly used in CNG service where added strength is needed due to heavy particulate loading and extremely contaminated coalesced oil. Optional Exterior Cage only is designated by the suffix X1. Good to 900°F.
Technical Information:
Efficiency at 0.01 microns. To Suffix Grade designation:
99.99998%99.9999%+99.99%+99.5%+95%
+75%30CSX340CSX350CSX360CSX370CSX3
80CSX3Our 70CSX3 grade is recommended for optimal filtration by providing high flow rates and long element life at peak efficiency.
All of our coalescing elements can be caged by adding suffix X3; including the C and RC Grades.
*X3 Caged inside and out are not compatible with our standard Aluminum or Brass housings.
Elements are designed for high pressure coalescing and/or systems with high differential pressure. These elements consist of a borosilicate glass inner layer sandwiched between two, rayon/phenolic layers. The reinforced inner/outer layers provide excellent strength.
Typically Used in Extreme Coalescing Service.
Technical Information:
Efficiency at 0.3 microns. Suffix Grade designation:
99.99998%99.9999%+99.99%+99.5%+95%
+75%N/AN/AN/AN/ARC
N/AOur RC grade is recommended for optimal filtration by providing high flow rates and long element life at peak efficiency.
Our DPCS elements incorporate an inner reinforced pleated microglass 3 micron pre-filter encapsulated with an outer microfiber glass coalescing layer. The pleats provide excellent dirt holding capacity, protecting the coalescing layer allowing it to drain liquids efficiently. This cartridge combines the pleated and coalescing elements into one package. We typically recommend this on our larger vessels which hold 2” diameter elements; i.e. 51-230 & 51-476 sizes.
Technical Information:
Efficiency at 0.01 microns. Suffix Grade designation:
99.99998%99.9999%+99.99%+99.5%+95%
+75%N/A40DPCS50DPCS60DPCS70DPCS
N/AOur 70DPCS is recommended for optimal filtration by providing high flow rates and long element life at peak efficiency.
Compressed air/gas applications: The PEL elements may be utilized as pre-coalescers or initial coarse filters in heavily contaminated systems. The 75-micron grade is recommended for this task since it exhibits the best flow curves, low initial DP.
Technical Information:
PEL filter elements are constructed from virgin polyethylene (H.D.P.E.). The material is in powdered/granular form and then compressed into a sintered tube. This process allows the filter element to be free from foreign binders. Thus, the only compatibility issue is with polyethylene. No end caps or gaskets are necessary to seal the element into place. Axial compression is used to create a seal on the flat surface of the element. The PEL elements are naturally hydrophobic.
These coalescing cartridges were specifically designed for use in our SLH800 series filter housings. Ideal for compressed air/gas applications where a low pressure stainless steel housing is required.
Technical Information:
Efficiency at 0.01 microns. Suffix Grade designation:
99.99998%99.9999%+99.99%+99.5%+95%
+75%N/AN/A50CSN/A70CS
N/AOur 70CS is recommended for optimal filtration by providing high flow rates and long element life at peak efficiency.
For more information Plate Disposable Filter, please get in touch with us!